Cisco CCNP / BSCI Tutorial: Comparing OSPF and ISIS Hellos

While studying to pass the BSCI exam and preparing to earn your CCNP certification, you'll quickly notice that while OSPF and ISIS are both link-state protocols, there are a lot of differences between the two. One major difference is the way the two protocols handle hello packets.

Hello packets are imperative to keeping OSPF and ISIS adjacencies alive. Since they are both link-state protocols, neither of them will send updates at any specified time. Hello packets are the only method by which routers running OSPF and ISIS can see that a neighboring router is still available.

OSPF gives us some great options when it comes to keeping routing table size down via the use of stub and total stub areas, but to OSPF, a hello packet is a hello packet. ISIS routers are capable of sending two different types of hellos - Level 1 and Level 2.

ISIS routers are classified as Level 1 (L1), Level 2 (L2), and Level 1-2 (L1-L2). By default, Cisco routers are L1-L2 routers; this means that every ISIS-enabled interface will send out both L1 and L2 hellos.

If one of the interfaces is forming only an L1 or L2 adjacency, there's no reason to send out hellos for the other adjacency type. For example, if R1 is forming an L1 adjacency with R2 via its ethernet0 interface, there is no reason to allow the router to transmit L2 hellos. To hardcode a router interface to send only L1 or L2 hellos, use the isis circuit-type command.

R1(config)#interface ethernet0

R1(config-if)#isis circuit-type level-1

Note: To configure this interface to send only L2 hellos, the full command is "isis circuit-type level-2-only", not just "level-2".

This configuration would prevent L2 hellos from being transmitted out ethernet0. While this does save router resources and prevents unnecessary bandwidth usage, there is also no way an L2 adjacency can be formed - so double-check your network topology before using this command!

Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology

When you're studying to pass the BSCI exam and earn your CCNP certification, you're going to be introduced to ISIS. ISIS and OSPF are both link-state protocols, but ISIS works quite differently from OSPF. You must master these details in order to earn your CCNP.

One of the major differences between OSPF and ISIS will be evident to you when you first begin your BSCI exam studies, and that is the terminology. ISIS uses terms that no other protocol you've studied to date uses, and learning these new terms is the first step to BSCI and CCNP exam success.

First off, what does "IS" stand for in "ISIS"? It stands for "Intermediate System", which sounds like a group of routers. As opposed to Autonomous Systems, which are logical groups of routers, an Intermediate System is simply a single router. That's it.

You'll also become familiar with End Systems, referred to in ISIS as an "ES". The End System is simply an end host.

ISIS and OSPF both use the concept of areas, but ISIS takes a different approach to this concept. ISIS routers use three different types of routing levels, according to the area a router has been placed in. Level 2 routers are connected only to the backbone and serve as a transit device between non-backbone areas. Level 1 routers are totally internal to a non-backbone area.

ISIS uses both Level-1 and Level-2 Hellos, meaning that the two types of routers just mentioned cannot form an adjacency. Luckily for us, there is a middle ground, and that is the Level 1-2 router. These routers connect non-backbone areas to backbone areas. L1-L2 routers keep two separate routing tables, one for L1 routing and another for L2 routing. This is the default setting for a Cisco router, and L1-L2 routers can form adjacencies with both L1 and L2 routers.

Part of the challenge of learning ISIS is getting used to the differences between ISIS and OSPF. Keep studying the terminology, master one concept at a time, and soon you'll be a master of ISIS and a CCNP to boot!

Cisco CCNP / BSCI Exam Tutorial: 10 ISIS Details You Must Know!

Earning your CCNP certification and passing the BSCI exam depends on knowing the details of many Cisco technologies, ISIS chief among them. To help you prepare for exam success, here's a list of ISIS terminology and basic concepts that will help you pass this tough exam. Enjoy!

ISIS Terms:

Domain: section of the network under common administrative control

Area: logical segment of the network composed of contiguous routers and their data links

Intermediate System: A router.

End System: A host device.

The four levels of ISIS routing:


Level 0: ES-IS routing in the same subnet.

Level 1: IS-IS routing in the same area.

Level 2: IS-IS routing in the same domain.

Level 3: Inter-domain routing performed by InterDomain Routing Protocol (IDRP).

ISIS Adjacency Possibilities:


L1: Can form adjacency with any L1 in the same area and any L1/L2 in the same area.

L2: Can form adjacency with any L2 in any area, and with an L1/L2 in any area.

L1/L2: Can form adjacency with any L1 in the same area, L1/L2 in any area, and L2 in any area.

A router interface’s SNPA (Subnetwork Point Of Attachment) is its highest DLCI number if it’s on a Frame network, and its MAC address if the interface is on an Ethernet segment.

ISIS Hello Types:

ESH: ES Hello – Sent by End Systems to discover a router.

ISH: IS Hello – Send by Intermediate Systems to announce their presence. End Systems listen for these.

IIH: IS-to-IS Hello – Send by one IS to be heard by another IS. These hellos makes IS-IS adjacencies possible.

Best of luck on your CCNP exams!